Paper Servo Type Three In One 5 Ply Automatic Laminating Machine
Intelligent Good Service
1. Performance characteristics
1. Digital design of the entire machine, one click adjustment.
2. Electrical configuration: International brands such as PLC
Siemens and main motor Siemens.
3. Adopting a reflux glue system to reduce glue loss and stabilize
the glue adhesion effect.
4. Adopting a dual servo face paper correction structure, the face
paper and tile paper (card paper) are automatically detected and
servo corrected, ensuring high precision in tracking and adhering
to the front gauge of the face paper and tile paper (card paper).
The front gauge can be adjusted independently according to product
needs.
5. The host adopts a large roller (160mm) design for stable
operation and high efficiency. The stainless steel mesh roller of
the large roller (160mm) is evenly coated with glue, saving glue
amount and not throwing glue.
6. The surface of the laminating roller and pressing roller is made
of special polyethylene material, and the glue automatically falls
off and is free from wiping.
7. The tile paper feeding structure adopts a leading edge feeding,
an extended and widened belt with large suction to ensure stable
tile paper and cardboard feeding without damaging the cardboard.
8. Laminating: cardboard+cardboard, cardboard+gray
cardboard+cardboard, corrugated+cardboard, corrugated+corrugated,
corrugated+corrugated+cardboard, etc.
9. The three in one laminating machine can complete the lamination
of three or two cardboard sheets at once, and can produce products
such as two-layer boards (cardboard+cardboard), three-layer boards,
four layer boards, five layer boards, seven layer boards, etc.
2. Parameters:
| Model | SFC1900 | SFC2200 |
| Max size | 1900*1900mm | 2200*2200mm |
| Min size | 500*500mm | 500*500mm |
| Top sheet thickness | 120-800g/㎡ |
| Bottom sheet thickness | ≤10mm |
| Work speed | 160m/min |
| Power | 24kw | 24kw |
| Stick accuracy | ±0.8mm |
3. BRANCH INTRODUCTION:
1. Bottom Paper Feeding
The two bottom feeding part adopts lead edge feeding, the wheels
use unidirectional bearing (reduce the wear of rubber wheels). The
wide rubber wheels ensure that the E, F, and G corrugated does not
deform.
Two sets lead edge feeding system, suction is greater, the
stability is higher, and the cost of use is lower.
2. Top Sheet Feeding
Equipped with high speed feeder, and together with Becker vacuum
pump. The front and rear of feeder are controlled by the servo
motor. After input paper size, it will be automatically positioned.
Both paper lifting and forwarding sucker can freely adjust to
ensure that whether thick or thin paper can be delivered rapidly
and smoothly.
3. Eelctrical System
Mainly using Siemens electric system to ensure machine stability,
high efficiency and low failure. Using man-machine interface and
PLC combination, display all the information on the screen.
Machine has 7-9 servo motors.
Mainly use SKF and NSK bearings.
4. Pre-Stack Part
Pre-stack pile of paper under the condition of non-stop, improve
efficiency. The width of the pre-stacker is controlled by the
motor, the size of the paper is automatically positioned. The
dual-use lifting platform, we can use the pre-stacker structure to
push the pre -pile of paper into the platform. We can also push the
stack of paper directly into the platform. And the platform can be
adjusted around the actual situation of the paper stack.
5. Positioning System & Glue Roller
Equipped with sensors and servo motor, control top sheets to do
independent compensation action to make sure high accuracy. The
design of large stainless steel anilox roller (160mm in diameter)
is stable and high-efficiency, coat evenly and save glue volume.
Use a circulating glue system to reduce glue loss and stabilize
glue adhesion effect.
6. Automatic Lubrication System
Lubricate the bearing regularly to prolong the service life of the
bearing and save the cost.
7. Anilox roller & Pressure roller
Anilox roller diameter is 160mm, In the case of high -speed
running, the roller speed is still very slow and does not shake the
glue.
Pressure roller diameter is 150mm, Special materials on the
surface, do not stick glue, free to clean.
4. Floor Drawing
